When the time expires, the timer will send "done" back on the same channel. Send a number representing a time in seconds, from 0.5 to 3600. The camera will search for a node "distance" meters away and up to 10m down.Įvery second while a player is within "radius" meters of that point, a table listing the players in range will be sent via digilines on the chosen channel.Īfter setting the channel, send a number from 0 to 14 to set the light level. The HTTPRequestResult table will be sent back on the same channel. Send a digilines signal with the URL you want to download. If unlocked, anyone can use the buttons, although channel setting and (for reasons that shuld be obvious) locking/unlocking is still limited to the area owner and players with protection_bypass.
If locked, only the owner of the area is allowed to use the buttons. Click the padlock icon to lock/unlock it. There is also a "lock" function in the bottom-right of the "LCD" area.
#MINETEST DIGILINES MODS#
If the panel is placed in a protected area (all standard protection mods are supported), only the owner of the area (and players with the protection_bypass privilege) can set the channel. The buttons, when pressed, send the messages "up", "down", "left", "right", "back", and "enter" on the same channel. Once a channel is set, any messages sent on that channel will be shown on the "LCD". Set a channel and radius (radius must be a number >0 and <10 - anything invalid will be ignored and "6" used instead).Įvery second while a player is within the radius, a table listing the players in range will be sent via digilines on the chosen channel.
#MINETEST DIGILINES HOW TO#
How to use the digilines player detector: Insulated digilines conduct like regular digilines, but only into/out of the ends of the "wire" or at locations where an intermediate connection has been placed. Signals can only be conducted into or out of the stack at these "plates". Vertical digilines will automatically connect to other vertical digilines directly above or below them, and form "plates" on each end of the stack. These work exactly like the mesecons equivalents, that is: It conducts digilines signals (like digilines) in all directions (like mese). Note that the settings cannot be changed after setting - you must dig and re-place the knob to do so. If the "protected" checkbox was checked, then only players allowed to interact in the area can do this.Įach time the setting is changed, the new setting is sent on the selected channel. Left-click to decrease the current setting or right-click to increase it. Note that the settings cannot be changed after setting - you must dig and re-place the button to do so.Ĭonnect to a digiline, right-click, and set the channel and the minimum and maximum values. If the "Manual Light Control" checkbox is checked, the light will not illuminate automatically when the button is pushed - use the "light_on" and "light_off" commands to control it. If the "Protected" checkbox is checked, only players allowed to interact in the area can push the button. When the button is pressed (right-click), it will send that message on that channel, over digilines. Only needed for craft recipes: default, basic_materialsĬonnect to a digiline (or digimese), right-click, and set a channel and message. Optional: mesecons_noteblock (for digilines noteblock), mesecons_mvps (for digilines piston), mesecons_luacontroller (for I/O expander) Required: digilines (base only) and mesecons (base only) Textures WITH "adwaita" in the file name - These are icons by the GNOME Project, licensed under GNU LGPL v3 or CC BY-SA 3.0. Textures WITHOUT "adwaita" in the file name - CC BY-SA 3.0 Generic (contains modified versions of textures from mesecons and digilines)
#MINETEST DIGILINES CODE#
ZIP TAR.GZ tuedel 19745570fe Replace wall knob model with nodeboxĪdd sounds for digtron and scifi_nodes modsĬode - LGPL v3 or later (contains some code from mesecons and digilines)
0 kommentar(er)
